Approximate number of beads of various lengths: round beads are available in many sizes and are measured according to the beads diameter in millimeters (mm). Beads are usually pre-strung and typical length of the strand will be approximately 16″.
The average 16″ strand will contain the following number of beads:
•4mm= approx. 100 beads
•5mm= approx. 80 beads
•6mm= approx. 67 beads
•7mm= approx. 57 beads
•8mm= approx. 50 beads
Because you may wish to include a mixture of sizes in the necklace or bracelet, it is important to know how to determine just how many beads of a given size will be required. It is fairly simple to figure out the number of beads needed for a length of finished strand and the easiest method it as follows:
1.one inch = 25.4 mm
2.multply 25.4 by the number of beads (excluding clasp) in the finished strand. for example: the strands will be 16″. 16″ x 25.4 mm = 406.4 mm
3.divide the total number of millimeters in the final length (in this case, 406.4mm) by the diameter of the beads to be used (let’s use 4mm), and the result wll be the number of beads. For example, 406.4mm (16″) divided by 4mm = 101.6 beads.
Remember when computing the length of the finished strand, to provide any findings such as clasps that will be included in the design, these will increase the length from 1/2″ to an inch or 1 1/2″ depending on your choices.
Threads, Findings and Equipment
While beads are the main ingredient of the necklace or bracelet, other materials, such as thread or wire and clasps are very important, additionally, there are a variety of tools that you will find extremely helpful, and a good working environment is essential.
The selection of threading materials varies as the beads themselves. String cord or wire is manufactured with a very tight twist that provides the material with strength and durability and is sometimes coated for additonal protection. Stringing thread or wire can be obtained on cards or spools. The most important qualities to look for when selecting thread or wire are the that the thread will pass through the smallest borehole of the beads, and that it is strong enough to support the weight of the finished bead.
The following describes which stringing material is best for various beads:
•pearls–silk thread
•beads with smooth drill holes–silk, polyester or nylon
•beads with abrasive holes–polyester or nylons
•beads with metallic, large or large bore drill holes –tigertail or foxtail
•ropes or woven necklaces–nylon
Findings: the term ‘ findings’ is used throughout the jewelry industry to collectively describe a variety of prefabricated items such as, jumprings, bead tips, headpins, clasps. These items are useful and necessary for the ease and comfort of the wearer in putting on and removing, they provide the means of connecting strands and they add a touch of quality to your design.
•Headpins: the headpin is a length of wire with a flat at one end. It is used to string a bead, or several beads, then connect them to the strand by making a loop at one end.
•Clasps: Clasps do just that–clasp strands together. As with the bead they are connecting. Clasps come in a variety of shapes and styles. Some connect both ends of a single strand, some connect several strands, individually, while others accomodate a wide range of several strands together. Clasps can be simple or very ornate. Some are made so that they are not seen as a clasp, but part of the overall design.
Tools & Equipment
•Pliers: a pair of pliers is a must for closing bead tips, opening and closing jumprings and it can be used to help tighten knots. Chain nose pliers are the most practical kind to use, because the outside of the nose is rounded, while the inside is flat or gripping, the tip of the plier should be long and narrow.
•Ruler: a 24″ ruler, marked in millimeter’s as well, will be necessary to keep track of the length of the strand on which you are working.
•Scissors: scissors are another must in your jewelry making tool kit, especially if working with thread. The best kind are not too large and they must be very sharp.
•Glue: you will need fast-drying type of cement that the jeweler’s use.
•Beading Boards are optional but are great to keep your area organized. These resemble trays and enable you to layout your designs without having beads rolling all over the floor. Some have compartments to hold the beads you are currently working with, and some have a pre-measured layout to help determine the length of the desired necklace or bracelet.
The importance of a good working environment cannot be stressed enough–the successful completion of a project, with comfort will depend on how well you have selected your beading niche. The ideal space will be well-lit and contain a sizeable work surface to provide enough room for all beading materials and equipment. Beads bounce, roll and slither, therefore, your work surface should be a non-stick variety. Felt, velvet or a scrap of carpet, or a towel. Any of these are suitable and will prevent any untimely bead escapes, resulting in frustrating searches on your hands and knees.
The overall size of the work area is important too! It is amazing how much room is needed for containing beads,threading materials and supplies.
•Useful guide for selecting the right wire for your beading projects:
.10″–Excellent for beading weaving, Peyote stitch, and small seed beads
.012″/.013″– Great for Austrian crystals, seed beads and freshwater pearls
015″/018″– Most versatile size available–use with heavy beads, metal, ceramic and fiber optic beads
.020″/.021″– Use with metal, large or heavy beads with medium to large drilled holes. Such as garnet, crystal & glass
0.21″/.026″–Terrific for metal, large or heavy bead with large drilled holes such as African Trade beads.
Popularity: 6% [?]
Leave a Reply